Cement Drive Ball Mill Girth & Pinion Gearbox — Repair, Price & Specs
Open gearing — girth gear + pinion set · ratios single reduction · 2,000–12,000 hp. New price, used price, and a real standard-shop-vs-in-house repair comparison — actual cost and lead time — plus specs. Or sell your surplus Ball Mill Girth & Pinion for cash.
Have this unit? Snap the nameplate for an instant quote →
Ball Mill Girth & Pinion — price & lead-time compare
| New / retail (OEM)list price, new unit | $120,000–$400,000 |
| Used (working)secondhand, tested | $66,000–$300,000 |
Researched estimates anchored to OEM pricing; a new Ball Mill Girth & Pinion commonly runs a 16–30 week lead time for comparison. Send your nameplate for a confirmed number.
Why rebuild your Ball Mill Girth & Pinion with us
Decades in industrial gear
We’ve bought, sold, and rebuilt industrial gearboxes for years — we know the Cement Drive Mill Drives line, not just gears in general. That experience shows up in a correct diagnosis the first time.
Faster turnaround
Standard rebuilds ship in 5–14 business days with 24–72-hour emergency service — while a new unit can be 16–30 weeks out. We get your line running sooner.
Transparent price up front
You see the full picture before you commit — retail, used, surplus, repair, and a cash offer. Some shops take your unit in, tear it down, and only then hand you a quote you’re effectively forced to accept. We give you the numbers first.
We won’t hold your unit
Your gearbox is never held hostage. If repair isn’t the smart move, we’ll tell you — and we’ll buy the unit for cash so you walk away ahead instead of paying to get a paperweight back.
About the Cement Drive Ball Mill Girth & Pinion
The Cement Drive Ball Mill Girth & Pinion is a open gearing — girth gear + pinion set from Cement Drive’s Mill Drives line, rated 2,000–12,000 hp across ratios of single reduction, and commonly found on ball/sag mill drives. Because Cement Drive is the class of heavy mill, kiln, and VRM drives that keep cement plants running, these units turn up constantly for both rebuild and surplus buyback. When one fails the real question is never just "what does a repair cost" — it’s how our in-house repair cost and lead time compare to a standard shop, and how fast you can be running again. That side-by-side is exactly what the comparison above gives you, and it’s information most repair sites simply don’t publish.
On the Ball Mill Girth & Pinion, typical failure modes are bearing wear, shaft-seal leakage, and gear-tooth pitting from degraded or contaminated oil. Most units are fully rebuildable. A correct rebuild means full teardown, hot-tank cleaning, magnetic-particle inspection of all gearing for hidden cracks, verification of bearing-bore tolerances, new bearings, seals, shims and gaskets, reassembly to factory clearances, and a loaded run-test. Done right, that restores a fresh service life at a fraction of replacement — and our in-house cost and lead time come in below a standard shop, with the exact dollars and days shown in the comparison above, versus the 16–30 weeks a new Ball Mill Girth & Pinion can take to arrive.
Here’s the part worth being honest about: repair isn’t always the answer. If the housing is cracked or the gears are unavailable, a used, surplus, or reman Ball Mill Girth & Pinion may be cheaper and faster than rebuilding — and if that’s the case we’ll say so and buy your failed unit for cash rather than talk you into a repair that doesn’t pay. That two-way position is deliberate. A shop that only earns money when you repair has every reason to take your gearbox in, disassemble it, and hand you a quote you can no longer walk away from. We put every number in front of you first, and we don’t hold your equipment while we do it.
The Ball Mill Girth & Pinion should be rebuilt by an AGMA-experienced industrial gear shop with in-house gear cutting (hobbing and grinding) and NDT capability — not a general machine shop — and that is exactly the caliber of partner we route these jobs to. Combined with years in the industrial equipment business, that’s why the Cement Drive units we handle come back right the first time. And if you have surplus Ball Mill Girth & Pinion units on the shelf, they carry real value — send the nameplate and we’ll turn them into cash.
Cement Drive Ball Mill Girth & Pinion specifications
| Brand / line | Cement Drive — Mill Drives |
| Model / part number | Ball Mill Girth & Pinion |
| Type | Open gearing — girth gear + pinion set |
| Nominal ratios | single reduction |
| Power range | 2,000–12,000 hp |
| Size / frame | up to 40 ft girth |
| Typical applications | ball/sag mill drives |
| OEM lineage | MAAG / Flender / FLSmidth |
Confirm exact ratio and rating from your nameplate — we service and buy all configurations of the Ball Mill Girth & Pinion.
What a Ball Mill Girth & Pinion rebuild includes
Teardown & clean
Full disassembly, hot-tank strip, oil passages cleared.
Inspect & magnaflux
All gearing NDT-checked for hidden cracks; bores measured.
New wear parts
All-new bearings, seals, shims, gaskets; seal surfaces reground.
Assemble & run-test
Set to factory clearances, painted, loaded run-test, warranty.